Product Details Portlet

EE-SX301/-SX401 Photomicrosensor (Transmissive)

  • Incorporates an IC chip with a built-in detector element and amplifier.
  • Incorporates a detector element with a built-in temperature compensation circuit.
  • A wide supply voltage range: 4.5 to 16 VDC
  • Directly connects with C-MOS and TTL.
  • High resolution with a 0.5-mm-wide sensing aperture.
  • Dark ON model (EE-SX301)
  • Light ON model (EE-SX401)
RoHS Compliant
Note: This web page provides an excerpt from a datasheet. Refer to Product Datasheet and other applicable documents for more information.
Absolute Maximum Ratings (Ta = 25ºC)
Rated value
EmitterForward currentIF50mA (see note 1)
Reverse voltageVR4V
DetectorPower supply voltageVCC16V
Output voltageVOUT28V
Output currentIOUT16mA
Permissible output
POUT250mW (see note 1)
Ambient temperatureOperatingTopr-40ºC to 75ºC
StorageTstg-40ºC to 85ºC
Soldering temperatureTsol260ºC (see note 2)
Note:1.Refer to the temperature rating chart if the ambient temperature exceeds 25ºC.

2.Complete soldering within 10 seconds.

Electrical and Optical Characteristics (Ta = 25ºC)
EmitterForward voltageVF1.2 V typ.,
1.5 V max.
IF = 20mA
Reverse currentIR0.01µA typ.,
10 µA max.
VR = 4V
Peak emission wavelengthλP940 nm typ.IF = 20mA
DetectorLow-level output voltageVOL0.12 V typ.,
0.4 V max.
VCC = 4.5 to 16 V,
IOL = 16 mA,
IF = 0mA
IF = 8mA
High-level output voltageVOH15 V min.VCC = 16 V,
RL = 1kΩ,
IF = 8mA
IF = 0mA
Current consumptionICC3.2 mA typ.,
10 mA max.
VCC = 16 V
Peak spectral
sensitivity wavelength
λP870 nm typ.VCC = 4.5 to 16 V
LED current
when output is OFF
IFT3 mA typ.,
8 mA max.
VCC = 4.5 to 16 V
LED current
when output is ON
HysteresisΔH15% typ.VCC = 4.5 to 16 V
(see note 1)
Response frequencyf3 kHz min.VCC = 4.5 to 16 V,
IF = 15 mA,
IOL = 16mA
(see note 2)
Response delay timetPLH(tPHL)3 µs typ.VCC = 4.5 to 16 V,
IF = 15 mA,
IOL = 16mA
(see note 3)
Response delay timetPHL(tPLH)20 µs typ.VCC = 4.5 to 16 V,
IF = 15 mA,
IOL = 16mA
(see note 3)
Note :1.Hysteresis denotes the difference in forward LED current value, expressed in percentage, calculated from the respective forward LED currents when the photo IC in turned from ON to OFF and when the photo IC in turned from OFF to ON.

2.The value of the response frequency is measured by rotating the disk as shown below.


3.The following illustrations show the definition of response delay time. The value in the parentheses applies to the EE-SX401.

Note: All units are in millimeters unless otherwise indicated.


Terminal No.
VPower supply (Vcc)
OOutput (OUT)
GGround (GND)

Unless otherwise specified, the tolerances are as shown below.
3 mm max.± 0.3
3 < mm ≤ 6± 0.375
6 < mm ≤ 10± 0.45
10 < mm ≤ 18± 0.55
18 < mm ≤ 30± 0.65