G2RL-2 PCB Power Relays
Low profile power relay with 15.7 mm height, ideal for incorporation in miniature equipments
- A wide variety of single pole, double pole, high-capacity (16 A) type and high-sensitivity type (250 mW) relays are available.
- IEC/EN 60335-1 conformed. (-HA Model)
- Satisfies ambient operating temperature requirement of 85°C and 105°C (-CV Model).
- Clearance and creepage distance: 8 mm / 8 mm min.
- G2RL-1(A)-E-ASI: TV3 rating models available.
- IEC/EN 60079-15 conformed
(Except G2RL-1(A)-H, G2RL-1A-E-CV(-HA) Models).
- Reduced power consumption with voltage holding and pulse width modulation (PWM) control (only for G2RL-□-PW1 model).
|Terminal Shape||Market Code||Classification||Contact form||Enclosure rating||Model||Rated coil voltage||Minimum packing
|Standard||DPST-NO (2a)||Flux protection||G2RL-2A||5、12、24、48 VDC||20 pcs/tube|
|G2RL-2A-PW1||5, 12, 24 VDC|
|DPDT (2c)||Flux protection||G2RL-2|
|G2RL-2-PW1||5, 12, 24 VDC|
|Standard||DPST-NO (2a)||Flux protection||G2RL-2A-HA||5, 12, 24 VDC|
|% of rated voltage|
|5 VDC||80.0||62.5||70% max.||10% min.
10 to 41% *
Approx. 120 *
|48 VDC||8.96||5,358||Approx. 430|
|High sensitivity||5 VDC||50||96||75% max.||10% min.||Approx. 250|
Note 1. The rated current and coil resistance are measured at a coil temperature of 23°C with a tolerance of ±10%.
Note 2. The operating characteristics are measured at a coil temperature of 23°C.
Note 3. The “max. voltage” is the maximum voltage that can be applied to the relay coil.
* These numbers are only for -PW1 type. Power consumption with holding voltage is approx.120mW. Please confirm the detail in page 8 coil voltage reduction (holding voltage).
●Contacts: Flux Protection Type
|Standard type (resistive load)||High-capacity type (resistive load)||High-sensitivity type (resistive load)|
|Contact material||Ag-alloy (Cd free)|
|Rated load||12 A at 250 VAC
12 A at 24 VDC
|8 A at 250 VAC
8 A at 30 VDC
|16 A at 250 VAC
16 A at 24 VDC
|10 A at 250 VAC
|Rated carry current||12 A (See note)||8 A (70°C)/5 A (85°C)
|16 A (See note)||10 A (See note)|
|Max. switching voltage||440 VAC, 300 VDC|
|Max. switching current||12 A||8 A||16 A||10 A|
|Failure rate (P level)
|40 mA at 24 VDC|
* This value was measured at a switching frequency of 120 operations/min.
Note: Contact your OMRON representative for the ratings on sealed models.
●Flux Protection Type
|Standard type||High-capacity type||High-sensitivity type|
|Contact resistance *1||100 mΩ max.|
|Operate (set) time||15 ms max.|
|Release (reset) time||5 ms max.|
|Insulation resistance *2||1,000 MΩ min.|
|Between coil and
|5,000 VAC, 50/60 Hz for 1min|
of the same
|1,000 VAC, 50/60 Hz for 1min|
of different polarity
|Impulse withstand voltage||10 kV (1.2 x 50 μs)|
|Destruction||10 to 55 to 10 Hz, 0.75 mm single amplitude (1.5 mm double amplitude)|
|Malfunction||10 to 55 to 10 Hz, 0.75 mm single amplitude (1.5 mm double amplitude)|
|Malfunction||Energized: 100 m/s2, De-energized: 100 m/s2|
|Durability||Mechanical||20,000,000 operations (at 18,000 operations/hr)|
50,000 operations at 250 VAC, 12 A
30,000 operations at 24 VDC, 12 A
30,000 operations at 250 VAC, 8 A
30,000 operations at 30 VDC, 8 A
30,000 operations at 250 VAC, 16 A
30,000 operations at 24 VDC, 16 A
50,000 operations at 250 VAC, 16 A
50,000 operations at 250 VAC, 10 A
|Ambient operating temperature||-40°C to 85°C (with no icing or condensation)
-40°C to 105°C (with no icing or condensation) by G2RL-1A-E-CV
|Ambient operating humidity||5% to 85% (with no icing or condensation)|
|Weight||Approx. 12 g|
Note 1. Values in the above table are the initial values at 23°C.
Note 2. Contact your OMRON sales representative for sealed models.
*1. Measurement conditions: 5 VDC, 1 A, voltage drop method
*2. Measurement conditions: Measured at the same points as the dielectric strength using a 500 VDC ohmmeter.
*3. 1,800 operations per hour.
|PCB Mounting Holes (BOTTOM VIEW)
Terminal Arrangement/ Internal Connections
|PCB Mounting Holes(BOTTOM VIEW)
||Terminal Arrangement/ Internal Connections
(No coil polarity)
● Please refer to “PCB Relays Common Precautions” for correct use.
●Mounting Position Compared to G2R Model
Although the G2RL model and the G2R model are both low profile relays, their characteristics such as switching capacity are different. Be sure to check operation under the actual operating conditions before use.
The G2RL model is flux-resistant with two sealing holes on the case. Thus, do not clean the relay by boiling or soaking in water. Consult your Omron sales representative for sealed type relay.
●Using Relays in an Atmosphere Containing Corrosive Gas
Do not use relays in an atmosphere containing corrosive gas (sulfuric or organic gas). Otherwise, connection failure due to corrosion on the contact surface may lead to functional faults.
●Coil Voltage Reduction (Holding Voltage) after Relay Operation
・If the coil voltage is reduced to the holding voltage after relay operation, first apply the rated voltage to the coil for at least 100 ms, as shown below.
・A voltage of at least 55% of the rated voltage is required for the coil holding voltage. Do not allow voltage fluctuations to cause the coil holding voltage to fall below this level.
|Applied coil voltage||Coil resistance *||Power consumption|
|Rated voltage||100%||62.5Ω (5 VDC)
360Ω (12 VDC)
1,440Ω (24 VDC)
|Approx. 400 mW|
|Holding voltage||55%||Approx. 120 mW|
●Power consumption reduction of coil with pulse width modulation (PWM)
・Models with PWM drive capability (-PW1) can reduce coil holding current with PWM control. This function reduces power consumption by reducing the current held by coil.
・Apply the rated voltage for at least 100 ms at the time of relay operation.
・The following are our verification conditions. When using, it be sure to check the actual machine under the actual usage conditions.
■Example of drive circuit
■Conditions of validation carried out by OMRON
・Applied voltage: rated voltage
・Duty: 60% or more
・Frequency: 10 kHz or more
・Diode Vf: 0.4 V or less